A sheet metal gauge chart converts a gauge number into thickness in inches and millimeters. A higher number means thinner sheet, and the same number gives a different thickness in each metal. 14 gauge is 0.0747 in (1.897 mm) in carbon steel and 0.0641 in (1.628 mm) in aluminum.
Picture a drawing that says 16 gauge and nothing else. Read as carbon steel, it means 0.0598 in sheet. A stainless buyer expects 0.0625 in, and an aluminum shop cuts 0.0508 in. That 0.0117 in spread (0.30 mm) on one callout is enough to change a bend, a weld fit or a slot clearance. It is also why the sheet metal design rules in our design guide start with material and thickness.
This sheet metal gauge chart covers carbon steel, galvanized steel, stainless steel and aluminum in inches, millimeters and pounds per square foot. You will also find tolerance data, a method for measuring sheet you already have, and advice on writing thickness on a drawing so a supplier in another country reads it the way you meant.
How to read a sheet metal gauge chart
- Pick the table for your metal: carbon steel, galvanized steel, stainless steel or aluminum.
- Find your gauge number in the left column.
- Read across for thickness in inches, thickness in millimeters and weight per square foot.
- Treat the value as nominal, then check the tolerance section before you set a fit.
What does gauge mean?
Gauge is a leftover from weight-based buying, and it is not a unit of length. For carbon steel, the Manufacturers' Standard Gauge fixes each number by weight: 41.82 lb per square foot for every inch of thickness. A 16 gauge sheet is defined as 2.5 lb/ft², and 2.5 divided by 41.82 gives 0.0598 in. Every sheet metal gauge chart for steel traces back to that weight rule.
Two rules cover most of what a gauge table tells you. A higher number means thinner metal, so 10 gauge steel is 0.1345 in and 26 gauge steel is 0.0179 in. The same number also means a different thickness in each metal, and the tables below put those side by side.
Gauge numbers lose usefulness at both ends of the scale. Commercial steel sheet runs from about 30 gauge up to about 7 gauge, and heavier material is sold as plate. Many sources draw the sheet-to-plate line near 6 mm (0.25 in).
ASTM is not a fan of the system. The general requirements standard for stainless sheet, plate and strip, ASTM A480/A480M, discourages gauge numbers and calls the term archaic. Gauge still appears on US purchase orders every day, so a printed sheet metal gauge chart earns its spot on the desk.
Which gauge system applies to which metal?
A sheet metal gauge chart for steel, stainless or aluminum looks the same on the page and runs on a different scale for each metal. Most wrong-thickness orders trace back to a correct number read off the wrong scale.
Buyers who work with UK suppliers will also meet Standard Wire Gauge (SWG), a separate scale again. Once you settle on a thickness, our guide to how sheet metal parts are made covers cutting, forming, joining and finishing.
Sheet metal gauge chart for carbon steel (inches, mm and weight)
Use this table for hot-rolled and cold-rolled carbon steel, also called mild steel. 14 gauge steel thickness is 0.0747 in, or 1.897 mm. Weight follows from the 41.82 rule, so a 4 ft by 8 ft sheet of 16 gauge weighs about 80 lb (2.5 lb/ft² times 32 ft²).
Carbon steel gauge table (Manufacturers' Standard Gauge)
Galvanized steel gauge chart
Galvanized sheet follows the steel scale and adds the zinc layer. At 16 gauge the bare steel is 0.0598 in and the galvanized sheet is 0.0635 in. The zinc adds about 0.00375 in at every gauge, which shows as 0.0037 or 0.0038 in once rounded. Weights below include the zinc and add about 0.156 lb/ft². ASTM A653/A653M covers hot-dip zinc-coated sheet.
Galvanized steel gauge table
If a drawing needs a set thickness after coating, say so on the drawing. Without that note, the supplier cannot tell whether the number is base metal or finished sheet.
Stainless steel gauge chart for 304 and 316
Stainless runs a little thicker than carbon steel at the same number. This table suits 304 and 316 sheet. At 16 gauge, stainless gives 1/16 in (0.0625 in, 1.588 mm) and carbon steel gives 0.0598 in. At 14 gauge, stainless reads 0.0781 in (1.984 mm) against 0.0747 in for carbon steel.
Weights below use about 40.3 lb/ft² per inch, the basis common in published charts. Treat them as estimates and use the mill test certificate for billing weight.
Stainless steel gauge table
Aluminum sheet metal gauge chart
Aluminum follows the Brown & Sharpe scale, so it runs thinner than steel at the same gauge. This table suits 3003, 5052 and 6061 sheet. 16 gauge aluminum is 0.0508 in, about 15 percent thinner than 16 gauge steel at 0.0598 in. It also weighs far less, about 0.72 lb/ft² against 2.5 lb/ft² for steel. A 4 ft by 8 ft sheet comes to near 23 lb instead of 80 lb.
Alloy shifts the weight a little. 6061 runs a bit heavier than 3003 and 5052. ASTM B209 covers aluminum flat sheet, coiled sheet and plate. If you are still deciding between sheet, extrusion and casting, read when aluminum sheet is the right process first.
Aluminum gauge table (Brown & Sharpe)
Gauge to mm chart: one gauge, four metals
This gauge to mm chart lines up the common sizes. Use it when a supplier quotes in metric: pick the row for your gauge, then the column for your metal. 14 gauge is 1.897 mm in carbon steel, 16 gauge is 1.519 mm and 18 gauge is 1.214 mm. Aluminum is the thinnest column in every row.
Gauge to mm: common sizes across four metals
Read across a row to see how big the mismatch gets. At 10 gauge, aluminum (2.588 mm) is 0.828 mm thinner than carbon steel (3.416 mm).
How much can real sheet differ from the sheet metal gauge chart?
Treat every value in the chart as a target, not a guarantee. Every figure above is nominal. Mills roll sheet to a tolerance band that depends on thickness and width. A sheet bought by gauge can measure above or below the chart value and still pass.
Tolerance examples (galvanized steel)
Thinner steel sheets usually show a greater percentage difference in thickness. With 24 gauge galvanized steel, the tolerance is about 14% of the nominal thickness. US steel service centers refer to ASTM and AISI tables for these numbers. The actual limits can change based on the width of the sheet and its edge specifications. If exact sizing is important, check the relevant standard before making a decision.
A chart cannot show that swing in a single column, so write the tolerance on the drawing. Measure where the standard measures. In 2009, ASTM revised its steel sheet tolerance tables so the default tables apply 1 in. (25 mm) in from the edge, because rolling thins the sheet near the edge. At Wootz.work, thickness goes into our quality gates as a check-in against the drawing. The system is designed to flag a sheet outside tolerance before it moves to the next operation.
How do you measure sheet metal gauge on a sheet you already have?
- Clean the spot. Burrs, scale and paint add false thickness.
- Take three readings with a caliper or micrometer, each at least 1 in. from an edge.
- Average them, then find the closest gauge in the table for your metal.
- On galvanized or painted sheet, remember the coating is part of the reading.
- Confirm the metal from the mill test certificate or the spec sheet. The wrong metal's table gives the wrong gauge.
How do you choose the right gauge?
First, look at the load the part will carry and the shape it needs. From there, choose a sheet thickness that can handle the job without adding unnecessary weight. Thicker metal means higher manufacturing and shipping costs. You can use a sheet metal gauge chart to check the available thicknesses and find one that suits the load and forming process.
- Strength and stiffness set the lower limit. A simple cover can be thin, and a bracket that carries a motor cannot.
- Weight matters on moving parts. At the same gauge, aluminum weighs a fraction of steel.
- Thin sheet distorts more under weld heat, and thick sheet needs larger bend radii.
- The cutting process limits thickness too, so read up on metal laser cutting if your range is wide.
- Coatings, anodizing and powder coat add thickness, so state whether your number is before or after finish.
Should a drawing say gauge or millimeters?
Most sheet outside the US is specified in millimeters. A drawing that says 16 GA leaves an overseas supplier to guess the metal, the gauge system and the tolerance. Write the thickness as a decimal, keep the gauge as a reference, and name the material standard.
Keep a sheet metal gauge chart handy for the conversion, then write the millimeter value on the drawing. A sheet metal fabrication partner can convert gauge callouts for you, but a drawing that states millimeters removes the question before it comes up.
Buyer checklist for sheet metal thickness
- Name the metal and grade, such as 304 stainless, 5052 aluminum or ASTM A1008 cold-rolled steel.
- Write thickness in millimeters and inches, with the gauge from your sheet metal gauge chart in brackets.
- Check which tolerance applies and include the relevant ASTM standard.
- Make sure it's clear whether the coating is counted in the thickness.
- Ask the supplier for mill test certificates showing the heat numbers. Also, get a dimensional inspection report for the first articles.
- Check the available sheet sizes and stock before finalizing the design.
- Put one incoming sheet under a micrometer and compare it with the table.
Have your gauge callouts checked before the quote
Wootz.work runs a network of qualified manufacturing partners across India and Southeast Asia and adds its own engineering and quality systems on top. For sheet metal, the work starts on the drawing, before anyone quotes.
Our engineers check the gauge details on each drawing, refer to the correct conversion table and work out the thickness in millimeters. They verify the metal type and applicable standard before checking whether our partner mills stock that thickness. Every requirement on the drawing, including thickness and finish, is checked at different stages of production. If something falls outside the requirements, the system flags it. Each order comes with mill test certificates showing heat numbers, along with dimensional reports that compare actual measurements with the specified dimensions.
Offshore manufacturing isn't the right choice for every order. If you need a single prototype within the week, a local service center will usually be quicker. It makes more sense for repeat orders where the drawing stays the same, the thickness needs to be consistent across deliveries, and the order volume makes qualifying a partner worthwhile. In these cases, working with one manufacturing partner means your team doesn't have to keep following up with multiple suppliers.
Conclusion
A sheet metal gauge chart does its job when you read the column for your metal and treat every number as nominal. Carbon steel, galvanized steel, stainless steel and aluminum run on separate scales, and at 16 gauge the thickest and thinnest of them differ by 0.0127 in (0.32 mm). On your next release, state the thickness in millimeters, name the standard and write the tolerance on the page. The chart then confirms your intent instead of replacing it.
Send us your drawing. Your first quote comes with a free DFM review. If you want to check our finish and tolerances first, order a free sample box.